SBose DVD-4009 User Manual download pdf

The following is a brief description of the numbered remote

control buttons that are shown in the diagram on page 1. Refer

to your User’s Guide for complete information.

1. SETUP Special Key reserved for remote programming

functions.

2. INPUT Used to change the current A/V input of the

selected device.

3. INFO Displays on-screen information about the current

television program.

4. LANG Activates Closed Captioning on TV1.

5. GUIDE Displays the on-screen television guide which

provides information about current and future television

programming.

6. VCR Controls Buttons used for VCR play/stop/wd/rwd/

pause controls. These buttons can also be used for

VCR-like controls with VOD services.

7. OK Executes the currently selected menu option.

8. ENTER Conrms the channel number entered.

9. MOVIES Displays the VOD menu. (currently unavailable).

10. DTV Returns user to live programming.

11. RESERVED USE KEYS Reserved for future use.

12. POWER Turns the currently selected service on or o.

13. DEVICE KEYS Selects the device that you would like to

control. (STB/ , TV, AUX)

14. MENU Displays the on-screen menu.

15. EXIT Exits the current menu item.

16. CH Changes channel up/down. Page up/down in

the Guide.

17. LAST Changes channel to the most recently

viewed channel.

18. VOL Raises or lowers volume of the currently

selected device.

19. NAVIGATION KEYS Navigates right, left, up, down in the

on-screen guide.

20. SPECIAL FUNCTION Reserved buttons for future use.

21. NUMBERED BUTTONS Allows direct access to specic

channels and menu items.

22. MUTE Turns the volume of the currently selected

device o.

23. MEDIA Reserved for future use.

24. MUSIC Displays available music channels.

25. PHONE Displays the Caller ID Menu.

26. HELP Displays the on-screen help menu.

Understanding The RemoteQUICK-REFERENCE GUIDE Set the Remote Control ID

First, you must program your remotes for use with your Gateway.

The Gateway comes with 3 URC remotes. Each remote can be

programmed for use with a dierent TV/Room.

1. Press and hold the OK button on the Gateway front panel for

about 5 seconds. When the OK button is released, the Gate-

way front panel Standby/On LED blinks twice (alternates red

and green), then stays lit red to indicate that the Gateway is

now in programming mode.

Perform the following steps to program the TV and AUX device:

1. Locate the device code for your desired device in the device

code table provided on the back side. If you could not nd

the device code for your device or it does not work after try-

ing the listed device codes for your device brand, then you

can go to the next section to try the auto-search procedures.

2. Turn on your device and with media inserted (if applicable).

3. On the remote control, press a device key once (i.e., TV or

AUX). NOTE: Use the “AUX” mode key to program control of

VCR, DVD player, cable box, satellite set-top-box and audio

device.

4. Press and hold the “SETUP” key until the selected mode

key backlight blinks twice, then release “SETUP”. The device

mode key will light up.

5. Enter the four-digit device code for your device. If you

perform this procedure correctly, the selected device mode

key backlight will blink twice. NOTE: If you enter an invalid

device code, the selected device mode key will fast blink 7

times. Device program mode will be terminated.

6. Aim the remote control at your device and press the

“POWER” once. The device should be turned o. If it does not

respond, repeat the above steps.

Programming the Remote

The Enventis remote can be programmed to control your Digital

TV service and up to two other devices.

The remote can be setup by following these simple instructions.

Before you begin, check the following items:

• Your television(s) is tuned to the correct channel.

TV1 = Channel 10

TV2 = Channel 23

TV3 = Channel 39

• Two AA batteries are installed into the remote.

IMPORTANT: Use only new AA Alkaline replacement batteries to

insure consistent operation.

Autosearch For Other Devices

2. Identify the remote control, which is labeled with a number

1, 2, or 3 on the battery cover plate on the bottom of the

remote, as shown below:

3. Press and hold the STB button (Myrio button) on the remote

control for about 4 to 5 seconds. The “STB” button backlight

LED will light to indicate that the remote control is in regis-

tration mode.

Use the number keys to enter the remote control ID (same as

what’s on the back of the remote:

Remote Control ID 1: Operates TV1

2: Operates TV2

3: Operates TV3

4. If you press a key other than “1”, “2” or “3”, or if you do not

press a button within about 10 seconds, the STB button

backlight LED will turn o, and the remote control registra-

tion process terminates.

After you enter a registration event, the “STB” button back-

light LED on the remote control and the Gateway front panel

LED will blink twice to indicate that the registration process

was successful.

5. Repeat the four steps above for each remote control.

If your home entertainment device does not respond to the re-

mote control after trying all codes listed for you brand, or if your

brand is not listed at all, try searching for your code. For example,

after trying all of the code for your device you still cannot get the

remote control to operate your device, then:

1. Power on the device and on the remote control, press the

desired device key once. Then press and hold SETUP until

the device key blinks twice, then release SETUP.

2. Press the POWER key once and aim your new remote at the

device.

3. Press either the “CHANNEL UP” key or “CHANNEL DOWN” key

to do device autosearch.

Note: In this search mode, the remote control will send IR

codes from the library in 5 second intervals. The device key

will be on and blink every 5 seconds while in the device

search mode.

4. If the device turns o, a working code has been found. Press

“OK” once to lock in the code. The selected mode key will

blink twice.

5. If all code sets of that device are exhausted in the search and

the “OK” is not pressed, the selected device key will fast blink

7 times and the search mode will be terminated.

“OK” Button

on Gateway

Front Panel

Programming the TV Code and Other Devices

1 2

Summary of Contents

Page 1 - Autosearch For Other Devices

The following is a brief description of the numbered remote control buttons that are shown in the diagram on page 1. Refer to your User’s Guide for co

Page 2 - SATELLITE

Denon ...5006, 5026, 5027, 5052Fisher ...5042, 5044, 5049Gradiente ...5062Harman Kardon ...5008, 5038, 5046Hitachi ...5059Ibiza ...5006, 5

SBose DVD-4009 User Manual

Browse online or download User Manual for Portable DVD/Blu-Ray players SBose DVD-4009. Understanding The Remote QUICK-REFERENCE GUIDE

Summary of Contents

More documents for Portable DVD/Blu-Ray players SBose DVD-4009

Comments to this Manuals